COBHAM SOLO4 Especificações Página 57
- Página / 99
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
57
Software Version (Status Only)
This status information describes the version of the software running in
the SOLO transmitter product.
FPGA Version (Status Only)
This information is for domo engineering use only.
Chaining
Chaining allows multiple services to be sent via one RF link. A receiver
may be connected to a transmitter to form a chaining or relay link. To
allow this, the chaining interfaces provided on the first receiver must be
connected to the second trans
mitter. Three modes of operation are
supported - no chaining (default), chaining mode, and relay mode. The
chaining mode allows two services (remote and local) to be combined.
The relay mode allows just the remote service to be transmitted turning
off the local service.
For chaining mode to operate correctly, the second unit in the chain
must operate at twice the transmit data rate from the first. If th
e first unit
is operating in QPSK rate 2/3 the second unit must operate in 16QAM
rate 2/3. If the first unit is operating in QPSK rate 1/3 the second unit
must operate in QPSK rate 2/3. The units must have different chaining
numbers selected, and the different unit names. For the relay mode to
operate correctly the second unit must have the transmit rate greater or
equal to the first unit.
Chaining is a
licensable feature.
Options
Engineering – provides access to further diagnostic and calibration
features. The Diagnostic dialogue box must not be altered. The
Advanced Options dialogue box under the Engineering menu allows
the user to Change RS232 address, which can be useful when
connecting multiple units together via a multi drop RS485 bus for control
purposes. The Serial control dialogue box allows the use
r to change
timeouts used during the serial communications between the unit and
the controller.
Enable Polling – selecting this option makes the control application
automatically refresh the data presented to the user every few seconds.
Polling Options – selecting this option allows the user to define
parameters to be regularly polled.
Write Decryption Key – opens a dialogue box for entering an ABS or
AES
scrambling key, as 32 ASCII hexadecimal characters (0…F)
Write License Code – open a further box for entering license codes for
the activation of licensable features (e.g. AES scrambling) in the
transmitter. Contact domo for support in applying new licenses as
required.
Restore Defaults – restores factory default settings in the transmitter.
- SOLO2 and SOLO4 1
- Users’ Manual 1
- 1 Table of Contents 2
- 2 Change History 4
- • Advanced operation 5
- • Technical reference 5
- 4 Introduction 6
- 5 Warranty and Support 7
- 5.1 Warranty Cover 7
- 6.3 CE marking 8
- S-Band 10
- Made in the UK 10
- Controls 12
- Cables and Connections 15
- • Control 3m 16
- • DC Power 2m 16
- DC Power 17
- Video and Audio 17
- Antennas 18
- • Vehicle based applications 19
- Connections 22
- Square down-converter 24
- Video Output Connection 28
- • Current Draw – 0.9A at 12V 29
- • Current Draw – 1.0A at 12V 29
- Control Cable 30
- Data Connection 30
- Installation Notes 30
- 7.4 Powering on the System 31
- Diagnostic On Screen Display 32
- Using the SOLBAT 34
- Charging the SOLBAT 34
- Amplifier Connection 35
- DC Power and Control Cable 36
- • Vehicle applications 37
- • Aircraft applications 37
- • Long Range fixed links 37
- RF Connection 38
- 8 Advanced Operation 41
- Output Frequency (MHz) 43
- Bandwidth Mode 44
- Default Transmit Mode 44
- Scrambling 44
- File Options 44
- Advanced TX Controller Window 45
- Modulation Bandwidth 45
- Modulation Output 45
- Narrow Band FEC 46
- Narrow Band Guard Interval 46
- Narrow Band Modulation 46
- DVB-T Service Name 46
- DVB-T FEC 46
- Video Bitrate 48
- Horizontal resolution 48
- Audio Encoder 48
- Audio Input Level 48
- Unit Name 48
- Input Frequency (MHz) 52
- Service Name 52
- Descrambling 52
- Advanced RX Controller Window 53
- Narrowband / DVB-T 53
- Input Frequency 53
- FPGA Version (Status Only) 57
- Chaining 57
- 9 NETSTREAM IP Output Option 59
- 9.1 General Info 59
- 9.2 Streamer 59
- 9.3 Web Server 59
- 10 Software Decoder 62
- 10.1 General Information 62
- 10.3 Encrypted Streams 65
- 10.4 Main Decoder Window 67
- Enable audio 68
- Close window 68
- 11 Fault Finding 71
- 11.1 Indicated Faults 71
- 11.2 Fault Symptoms 72
- 12 LED Indicators 73
- 13.1 Input Status Page 74
- 13.2 RF Advanced Page 75
- 13.3 Engineering Data Page 76
- 13.4 GPS Overlay 76
- 13.5 Frequency Scan Page 77
- Quick Scanning Stage 78
- Service Scanning Stage 78
- Completed Scan 79
- Front Panel Control 80
- Control Commands 81
- Original OSD Mode 82
- OSD Timeout 83
- 15 Control Protocols 86
- 15.5 Receiver Command List 94
- 16 Default Configurations 98
Manuais e produtos relacionados com Recetor COBHAM SOLO4
Recetor COBHAM Messenger VETA Manual do Utilizador
(36 páginas)
(36 páginas)
Recetor COBHAM NanoVue Manual do Utilizador
(51 páginas)
(51 páginas)
Recetor COBHAM Messenger VETA Manual
(31 páginas)
(31 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais